Inverter Xtender XTH

(3000-12, 5000-24, 6000-48, 8000-48)

The serie Xtender offers a new function, the Smart-Boost, which enables to add the inverter power to another source, like for instance a genset or the shorepower, even in case of asymetric loads. It is also possible to add an Xtender to almost any other existing inverter in order to increase the power available.

The products of the Xtender-Series provide an unmatched freedom of use, thanks to their many functions. In a basic application, they offer together the functions of inverter, battery charger, transfersystem and assistance to the source.

These functions can be combined and controlled in a totally automatic way for an exceptional comfort and an optimal management of the available energy.

By the implementation of several units, it is possible to create a 3-phase source or to set them in parallel to increase the power available. Up to 9 inverters of the serie Xtender shall therefore be combined together.

The programmable auxiliary contacts allow as well the interconnection with existing systems or the implementation of extended functions. Fully programmable by means of its remote control, it enables the update of the software, making it an upgradeable product.

Multifunctional contacts

The potential free contacts can be programmed to provide many supplementary functions. They can react to each event, inside or outside of the inverter (presence of the grid, battery thresholds, alarm signal). The contacts can also be programmed as time switch or can be disabled during sensitive periods (night, weekend). They allow therefore the implementation of functions like the automatic start of gensets, the automatic disconnection of second priority users, the alarm signal, the conditional charge of the battery, etc.

Function Smart-Boost

The function Smart-Boost enables to add the inverter power to another source, like for instance a genset or the shorepower, even in case of asymetric loads. It is possible to add an Xtender to almost any other existing inverter in order to increase the power available.

Features:

Possibility to connect up to 3 Xtenders in parallel
Three-phase systems with up to 9 Xtenders
True sine wave voltage
Reliable and noiseless with any kind of load
Outstanding overload capabilities
Function Smart-Boost for assistance to the source even with difficult loads
Automatic reduction of peak loads (power shaving)
Automatic allocation of the power available (power sharing)
Standby level adjustable over a large range and from a very low threshold
Multi-stage programmable 4 STEP battery charger with PFC
Ultra-fast transfer relay
High efficiency
Ultra-fast regulation
Control by digital signal processors (DSP)
Full internal protection.

Technical data

Model	XTH 3000-12	XTH 5000-24	XTH 6000-48	XTH 8000-48
Inverter
Nominal battery voltage	12 V	24 V	48 V	48 V
Input voltage range	9.5-17 V	19-34 V	38-68 V	38-68 V
Continuous power 25 °C	2500 ВА	4000 ВА	5000 ВА	7000 ВА
Power Smart-Boost	2500 ВА	4000 ВА	5000 ВА	7000 ВА
Power 30 min. 25 °C	3000 ВА	5000 ВА	6000 ВА	8000 ВА
Power 5 sec. 25 °C	3 х Pnom
Max. efficiency	93 %	94 %	96 %	96 %
Load detection (standby))	2 to 25 W
Consumption OFF / standby / ON	1.7W / 2.2W / 14W	1.8W /2.5W / 20W	2.2W / 3W / 22W	2.2W / 3.8W / 34W
Cos φ	0.1-1
Output voltage	230 V (- 10 % / 0)
Output frequency	50 / 45-65 Гц +/- 0.05 % (crystal controlled)
Harmonic distortion	<2 %
Overload and short-circuit protection	Automatic disconnection with 3 time restart attempt
Overheat protection	Warning before shut-off - with automatic restart
Battery charger 6 step adjustable : I-U-Uo-Equalize-Uo(low)-U(periodic)
Charging current adjustable	0-160 А	0-140 А	0-100 А	0-120 А
Input current balance adjustment	1-30 А			1-50 А
Max. input voltage	265 Vac
Input AC voltage range	Adjustable threshold from 150 to 230 Vac
Input frequency	45 - 65 Hz
Power Factor Correction (PFC)	Yes, according to EN 61000-3-2
General data
Multifunction contact adjustable	2 independent contacts 16 A 250 Vac (potential free 3 points)
Max. current on transfer relay	30 А / 6.9 kVA			50 А / 11.5 kVA
Weight	34 kg	40 kg	42 kg	46 kg
Dimension h x w x l [mm]	220 х 290 х 500 mm			220 х 310 х 500 mm
Operating temperature range	-20 °C to 55 °C
Protection index	IP 23
Ventilation	Forced from 45 °C
Acoustic level	< 10 dB / < 35 dB (with / without ventilation)

Remote control and programming centre RCC-03

Thanks to its graphic display it provides many understandable indications on the state of the system. The remote control memorises and displays the events that occurred on an installation and so it does anticipate the problems that might appear. It gives access to the many adjustable parameters of the Xtender like the setting of the charge curve of the battery, the programming of the auxiliary relays or even, among others, to a lot of operation options. A place is dedicated to a SD card which will allow the parameters memorising, the data transfer or the software update.

Battery temperature sensor BTS-01

This sensor enables to accurately adapt the charge thresholds to the battery temperature.

Communication module 3ph and parallel PEM-01

Allows the setting in parallel or the implementation of a 3-phase system even when only a single-phase source is available.

Communication cable for 3ph and parallel CAB-RJ45-2 (2 m)

Allows the setting in parallel or the implementation of a 3-phase system even when only a single-phase source is available

Inverters in our internet shop

You can buy this and other inverters and UPS for your backup or stand-by power syste in our internet shop.

To configure your system properly, you should determine necessary capacity of the storage batteries. .

Please go to our Internet-shop, section "Power electronics" to select the best inverter for your power system.

Inverter Xtender XTH

(3000-12, 5000-24, 6000-48, 8000-48)

Technical data

Remote control and programming centre RCC-03

Inverters in our internet shop

:: menu

:: information

:: Search

:: TEXT_ICQ

:: banners